Local Services

Trailer Repair Shop Pomona CA

Camper Services Pomona

Published Jun 07, 25

11 min read

Table of Contents

– Camper Awning Repair Pomona, CA
– OCRV Center
– Camper Service Near Me Pomona, CA
– Camper Repair Shop Pomona, CA
– Camper Repair Shop Pomona, CA
– Camper Repair And Service Pomona, CA
– Pop Up Camper Repair Pomona, CA
– Camper Trailer Repair Near Me Pomona, CA
– Camper Service And Repair Pomona, CA
– Camping Repair Near Me Pomona, CA
– Camper Roof Replacement Pomona, CA
– Camper Repair Near Me Pomona, CA
– Rv Camper Ac Repair Pomona, CA
– OCRV Center

Camper Awning Repair Pomona, CA

OCRV Center

23281 La Palma Ave Yorba Linda, CA 92887
(714) 909-1444
OCRV Center

A lot of campers around us had their awnings released. We returned home yesterday in the rain, so today I deployed the awnings to dry them out.

It appears that concerning 18 to 24 inches of the metal extrusion (rain gutter) that the awning is moved into has retreated from the wall and twisted a bit - Camper Services Pomona. I'm thinking the repair work will entail replacing that entire length of gutter (10 feet?) and possibly utilizing larger gauge screws to change those that were drawn out

We have actually obtained damaged brackets on our camper awning. 2 months earlier, we had a bad tire blow-out that triggered a curved axle, significant repair work, etc, and we wonder if the brackets cracked/broke throughout the bouncy ride prior to we understood the axle remained in difficulty. We have not had the awning out because it was in the shop to be fixed.

Camper Service Near Me Pomona, CA

The awning itself, springtime mechanism, etc, is great. The rear bracket setting up is fine, but the front one is cracked at the base and entirely broken through at the top, so that the top assistance arm no much longer attaches to the camper.

Even the actual assistance arms are intact. They are white metal (? The real arms are entirely normal/functionalI'm simply wanting to make certain we're not being taken in out of our despair (Camper Services Pomona).

Camper Repair Shop Pomona, CA

Are they that brand-specific and proprietary that if one piece is damaged it needs to be entirely changed? The recreational vehicle is a 2007, however we had rainfall damage in 2010 and the whole awning was brand-new back then. If nothing else, we would certainly like suggestions as to exactly how we can "jerry gear" this for some time - perhaps even get us through the summer - without having to place in an all new awning! We're in an extremely major bind because we have actually a journey planned in mid June that is not optional and can not be changed or delayed.

If we have to go awning-less, we will, but I 'd rather find a quick and effective option. Any individual? Please!.

Welcome to my Motor Home Improvement Series!.?.!! I'm on action 5 of replacing the roofing system of my '93 Fleetwood Jamboree Searcher motorhome. In the last action I got rid of the roof trim molding from three sides of the roof. In order to remove the 4th one, I need to eliminate the RV awning.

In order to replace the rubber roof and roofing system outdoor decking, I require to remove the awning. My recreational vehicle awning has legs which pivot at the base however can be eliminated to establish on the ground. I drew these out. Pushing this lever releases the foot of the awning legs.

Camper Repair Shop Pomona, CA

You'll additionally notice how the bracket is hooked on top of the trim molding that holds down the fiberglass panel in the back corner. That's why the awning requires ahead off first prior to the final steps of this blog post (revealing the front and back edges of the roofing outdoor decking).

Below's an information of exactly how the awning mounting brackets are screwed right into the camper. I didn't actually need to do this action up until the awning was on the ground yet I saw this established screw right here holding the awning canvas into the awning rail (there's another at the ideal end of the awning.) I went on and loosened it.

Once both screws are gotten rid of, simply draw back on the bracket. Loosening the large lag screws that hold the motor home awning mounting braces to the camper (with an outlet wrench) Getting rid of the placing bracket once the lag screws have been unscrewed. Keep in mind how this end was hooked over the termination bar that seals the spherical edge at the rear of the roof.

Both lag screws removed from the awning installing bracket on the. Getting rid of the placing brace of the awning.

Camper Repair And Service Pomona, CA

To replace the roofing, this awning bar needs to be eliminated. If you're simply changing your awning and not fixing the entire roof like me, after that you would not need to remove the awning rail.

Dropping the legs a few notches to decrease the entire awning. Currently I can reach this trim molding (the awning rail) quickly.

You might have to reduce completion with an energy blade if it is wrapped under. After that just pull it out! As soon as the vinyl screw cover insert was out I eliminated the screws with a cordless drill and the outlet head from my ratchet screwdriver set. This went pretty rapidly.

Once the screws were out I began prying up the awning rail. (There will be some butyl tape or putty sticking it to the rubber below.) HEADS UP! When I started to tear off the awning rail, the whole thing all of a sudden snapped off and rolled up into the awning like a home window blind.

Pop Up Camper Repair Pomona, CA

Simply understand it's coming! As soon as the screws are gotten rid of, the awning rail can be torn up. You can see the side of the rubber roofing that was attached under it. Once you begin pulling the awning rail away it will suddenly snap totally free and roll up like a window blind with the awning.

This thing is heavy so if you're working alone like me after that decrease it the ground little by little by walking the legs far from the camper on each side individually until you can lay it on the ground. I flipped the legs back up and out of the way against the camper.

After that I leaned the legs back against the camper. As soon as the awning got on the ground I eliminated the little collection screw at the best end of the awning, (I eliminated the one at the left end earlier.) These screws maintain the awning canvas from moving in the rail. Once they're removed the rail simply slides straight off the canvas by gliding the entire rail to one side.

Camper Trailer Repair Near Me Pomona, CA

When the two set screws were eliminated I might move the entire awning rail right off the awning. An additional look at the profile of this trim molding (the awning rail) after it was removed.

The next thing holding down the motor home fiberglass siding panels is the edge trim molding shown right here. It has a plastic screw cover strip inserted, so once again I just tore up the plastic insert and drew out enough so I can unscrew some screw heads.

I may finish up eliminating it later on if I require to replace the luan plywood underneath this fiberglass shift. The roof decking plywood expands under the fiberglass skin at the back of the camper. In order to change it, this fiberglass transition need to be lifted. To lift that, the corner molding should be removed.

After that I could swing the trim mold and mildew off the side enough to raise the edge of the fiberglass panel. When I can turn that piece of corner molding off the side, I began to tear up the fiberglass panel. It has glue under it and bits of rusted staples and sheared off screws still holding it in position.

Camper Service And Repair Pomona, CA

I switched from a scraper to a tight 6 wide putty blade. This item broke out of the fiberglass panel when I was attempting to pry it up. Then I switched over from a scrape to 6 inch large taping blade. Then I loosened the other edge trim in the very same way, and curved it laterally just enough so that I could raise the side of the fiberglass panel.

I located a lot of water damages in the plywood under the fiberglass panel so I'll probably be changing it. I had a significant quantity of water damage in the joint in between the rounded corner and the roofing deck.

Camping Repair Near Me Pomona, CA

The side of the roofing system outdoor decking is revealed at the back of the camper! I have actually exposed the roof substrate at the back side of the camper. Currently its time to discover the front edge.

Once again, I tore that layer up too (there had not been much stifling yet adhesive at this moment) and then I might tug out the rest of the rubber roofing that was glued below it. Currently I can take out the last little rubber roofing from underneath the fiberglass and luan plywood.

Camper Roof Replacement Pomona, CA

I saw there were no bolts holding the roofing system plywood down. I can see the blue styrofoam insulation under the damaged locations of luan plywood on the roof. Notice there are no fasteners at all holding down the roof plywood!

Once I scuffed up some of the broken little bits I obtained hold of a solid item of plywood and began to pull. The whole point started to pull up easily in one item without harming the foam board insulation at all.

There is a metal enhanced tape on the bottom that signs up with the assemble. I don't know how specifically they took care of to glue whatever down so well and get this tape joining them from the bottom, but it was perfectly done. The pieces of roofing ply are joined together at the joints underneath with a metal-reinforced tape.

Camper Repair Near Me Pomona, CA

I promptly understood the roof covering was losing toughness and stiffness as I pulled up the top layer, so cracked it off prior to the very first seam. A close up of the metal framing in the roofing system: one inch wide, one and a half inches high. Below's a detail of the wiring in the insulation foam and the strong timber reinforcements where the antennas screw into the roofing system.

I found a bunch of water damages in the plywood under the fiberglass panel so I'll most likely be changing it. Which implies I'll finish removing those edge trim pieces all the way down. However we'll reach that later. I had a significant quantity of water damage in the joint between the rounded corner and the roofing system deck.

The edge of the roofing outdoor decking is exposed at the back of the camper! I have actually exposed the roofing system substrate at the back side of the camper. Now its time to find the front edge.

Once again, I tore that layer up also (there wasn't much quieting however glue at this point) and then I might tug out the remainder of the rubber roofing that was glued underneath it. Camper Services Pomona. Currently I can take out the last little rubber roofing from beneath the fiberglass and luan plywood

Rv Camper Ac Repair Pomona, CA

I observed there were no fasteners holding the roofing system plywood down. I could see the blue styrofoam insulation below the harmed locations of luan plywood on the roof. Notice there are no fasteners at all holding down the roof plywood!

As soon as I scratched up a few of the busted little bits I got hold of a strong item of plywood and began to pull. The entire thing began to bring up easily intact without damaging the foam board insulation at all. Currently I can see the steel framing underneath. After that the plywood began peeling up as one item, leaving all the styrofoam well undamaged.

There is a steel enhanced tape under that signs up with the assemble. I do not recognize just how specifically they managed to glue whatever down so well and obtain this tape joining them from the underside, yet it was perfectly done. The pieces of roof ply are signed up with together at the seams underneath with a metal-reinforced tape.

OCRV Center

Address: 23281 La Palma Ave Yorba Linda, CA 92887
Phone: (714) 909-1444
OCRV Center

I swiftly recognized the roof was shedding strength and stiffness as I pulled up the top layer, so split it off right before the very first joint. A close up of the steel framework in the roof covering: one inch wide, one and a fifty percent inches high. Right here's a detail of the wiring in the insulation foam and the solid wood supports where the antennas screw right into the roof.

Share us on...

Table of Contents

– Camper Awning Repair Pomona, CA
– OCRV Center
– Camper Service Near Me Pomona, CA
– Camper Repair Shop Pomona, CA
– Camper Repair Shop Pomona, CA
– Camper Repair And Service Pomona, CA
– Pop Up Camper Repair Pomona, CA
– Camper Trailer Repair Near Me Pomona, CA
– Camper Service And Repair Pomona, CA
– Camping Repair Near Me Pomona, CA
– Camper Roof Replacement Pomona, CA
– Camper Repair Near Me Pomona, CA
– Rv Camper Ac Repair Pomona, CA
– OCRV Center

Local Services

Navigation

Home